mirror of
https://github.com/dortania/OpenCore-Legacy-Patcher.git
synced 2026-04-17 21:24:40 +10:00
215 lines
10 KiB
Markdown
Executable File
215 lines
10 KiB
Markdown
Executable File
# Installing Windows in UEFI Mode
|
||
|
||
Modern versions of Windows officially support two types of firmware: UEFI and BIOS. Users may want to boot Windows through the OCLP Bootpicker, but only UEFI Installations of Windows will show up in the OCLP Bootpicker.
|
||
Many older Macs do not "officially" support UEFI Windows installations and will refuse to install or cause many issues, but OCLP can be used to prevent almost all of these installation and usability issues.
|
||
|
||
## Minimum Requirements
|
||
|
||
This guide will focus on the installation of Windows 10 without using Bootcamp Utility. Windows 11 should also work, but its quirks will not be covered.
|
||
|
||
* Due to hardware and firmware limitations, UEFI Windows installations are only recommended on the following machines:
|
||
|
||
* 2015 MacBook or newer (MacBook8,x+)
|
||
* 2011 MacBook Air or newer (MacBookAir4,x+)
|
||
* 2011 MacBook Pro or newer (MacBookPro8,x+)
|
||
* 2011 Mac mini or newer (Macmini5,x+)
|
||
* 2009[^1] Mac Pro or newer (MacPro4,1+), upgraded GPU is preferred
|
||
* 2010 iMac or newer (iMac11,x+), upgraded GPU is preferred
|
||
* 2009[^2] Xserve (Xserve3,1), upgraded GPU is preferred
|
||
|
||
|
||
[^1]: MacPro4,1 and MacPro5,1 systems experience issues with the Windows installer, see the DISM section for installation instructions.
|
||
[^2]: Theoretically supported, not tested. Follow DISM section, similar to Mac Pro
|
||
|
||
If your machine is not listed, UEFI Windows will likely still install, but you may face stability/driver issues.
|
||
|
||
## Disk Partitioning and Formatting
|
||
|
||
The following is required for installation:
|
||
* 8GB+ USB Drive for the Windows installer
|
||
* 30GB+ Free Space on an existing drive / empty drive for the Windows installation
|
||
|
||
### Formatting the USB Drive
|
||
|
||
Open Disk Utility in macOS and format the USB Drive as ExFat with the Master Boot Record scheme:
|
||
|
||
|
||
|
||
### Formatting the Target Drive
|
||
|
||
Next, select the drive you wish to install Windows in Disk Utility on and partition it as ExFat (If formatting the entire drive, ensure it's using the GUID Partition Table scheme):
|
||
|
||
|
||
|
||
If you plan to use the same hard drive for macOS and Windows, we recommend creating a dedicated partition just for OpenCore. This lets Windows have the ESP to itself and OpenCore can stay within it's own bubble.
|
||
|
||
Recommended size is 200MB and the partition format **must** be FAT32 for OpenCore to operate correctly. You will next want to install OpenCore onto the new partition, either moving from the ESP with [MountEFI](https://github.com/corpnewt/MountEFI) or rerunning the OpenCore-Patcher.app
|
||
|
||
* Note 1: For machines with dedicated drives for Windows, having different partitions for OpenCore is not required.
|
||
* Note 2: Having different partitions for OpenCore is also not required if the Windows boot files detected by the stock Bootpicker are removed. See "Removing the Windows option from the stock bootpicker" for further information.
|
||
* Note 3: We recommend uninstalling OpenCore from the ESP/EFI Partition when you create this new OpenCore partition to avoid confusion when selecting OpenCore builds in the Mac's boot picker.
|
||
|
||
|
||
|
||
## Creating the Windows Installer
|
||
|
||
The latest Windows 10 installation image can be downloaded from Microsoft using the following link:
|
||
|
||
* [Download Windows 10 Disc Image (ISO File)](https://www.microsoft.com/en-ca/software-download/windows10ISO)
|
||
|
||
Alternatively, TechBench provides an download interface for other builds of Windows 10 in several languages, hosted on Microsoft's servers:
|
||
|
||
* [TechBench by WZT](https://tb.rg-adguard.net/public.php)
|
||
|
||
Once the file is downloaded, mount the .iso image:
|
||
|
||
|
||
|
||
Then open terminal and use the `rsync` command with the disk image set as the source and your USB drive set as the target. (Replace "CCCOMA_X64" with the mounted image's partition name, and replace "InstallWin10" with your USB Drive's name).
|
||
|
||
```
|
||
rsync -r -P /Volumes/CCCOMA_X64/ /Volumes/InstallWin10
|
||
```
|
||
|
||
|
||
|
||
The `rsync` command will take some time, so get some coffee and sit back. Once finished, the root of the USB drive should look as follows:
|
||
|
||
|
||
|
||
* Ensure that these folders and files are in the root of the USB drive, otherwise the USB will not boot.
|
||
|
||
|
||
## Installation Process
|
||
|
||
Once you reboot your machine, you should see a new boot option in the OCLP Bootpicker labelled as "EFI Boot". It may or may not have the BootCamp icon.
|
||
|
||
:::warning
|
||
|
||
If you aren't booted into OCLP, you may see two boot options labelled "Windows" and "EFI Boot". Do not choose either of the options and boot into OCLP to continue.
|
||
|
||
:::
|
||
|
||
### Installation: Microsoft Method
|
||
|
||
Once booted into the Windows installer, proceed as you normally would on any Windows computer. If you see an error message containing “Windows could not prepare the computer to boot into the next phase of installation”, please follow the next portion of this guide (DISM Installation).
|
||
|
||
### Installation: DISM Deployment Method
|
||
|
||
Once booted into the Windows installer, proceed as you normally would until you reach the "Where do you want to install Windows" disk formatting section.
|
||
|
||
When you are prompted to select a drive, select your desired partition and delete it using "Delete". If you want to install Windows to an empty drive, erase every partition currently on the desired drive.
|
||
After your drive/partition is erased, press "New" to create the Windows system partitions.
|
||
|
||
|
||
|
||
You will be prompted to confirm the creation of the system partitions, press "OK".
|
||
|
||
|
||
|
||
Once the partitions are created, select the main (largest) partition and press "Format". This will format the partition using the NFTS file system.
|
||
|
||
|
||
|
||
After the installer formats the partition, open up the Command Prompt by pressing SHIFT + F10. Then run the `diskpart` command, and `list vol`. This will produce a list of volumes in your system, make sure to keep track of the drive letters of the main Windows partition (largest, NTFS), the EFI partition (100MB, FAT32), and the Windows installer (Usually Drive D). Run `exit` to close diskpart
|
||
|
||
|
||
|
||
Now, get a list of available Windows editions by running `dism /Get-WimInfo /WimFile:D:\Sources\install.wim` (substituting D with the Installer Drive Letter). This guide will use Option 6 for Windows 10 Pro.
|
||
|
||
|
||
|
||
You can now start the deployment process. Run `dism /Apply-Image /ImageFile:D:\Sources\install.wim /index:6 /ApplyDir:E:`, replacing "D" with the Installer Drive Letter, "6" with the Windows edition option, and "E" with the Windows Partition Drive Letter.
|
||
|
||
|
||
|
||
Once `dism` finishes its thing, run `bcdboot E:\Windows`, substituting "E" for the drive letter of the main Windows partition to create the boot files.
|
||
|
||
|
||
|
||
::: details Removing the Windows option from the stock bootpicker, HIGHLY RECOMMENDED FOR MACPRO4,1, MACPRO5,1, AND XSERVE3,1 SYSTEMS
|
||
|
||
Removing the Windows boot option from the stock bootpicker is HIGHLY RECOMMENDED on MacPro4,1, MacPro5,1, and Xserve3,1 systems in order to prevent Secure Boot NVRAM corruption and bricking.
|
||
|
||
Enter the EFI Folder by running `C:`, substituting "C" for the EFI Partition Drive Letter. Then run `cd EFI` to enter the EFI Partition. Next, run `rmdir Boot /S /Q` to remove the boot files that can be detected by the stock Bootpicker. The OCLP Picker will still be able to detect and boot Windows.
|
||
|
||
|
||
|
||
You can verify that the `Boot` folder is removed by running the `dir` command:
|
||
|
||
|
||
|
||
:::
|
||
|
||
Windows is now installed. It should be recognized as "EFI Boot" with a BootCamp icon in the OCLP Bootpicker.
|
||
|
||
## Post-Installation
|
||
|
||
### Installing BootCamp Software
|
||
|
||
To get started, download the Brigadier utility from the following link:
|
||
|
||
* [Download Brigadier](https://github.com/timsutton/brigadier/releases/download/0.2.4/brigadier.exe)
|
||
|
||
Once Brigadier is downloaded, move it to your desktop for easy access.
|
||
|
||
Open up a command prompt window as a standard user and run `cd desktop`.
|
||
|
||
|
||
|
||
Then run `.\brigadier.exe --model=MODEL1,1`, replacing "MODEL1,1" with your machine's SMBIOS model.
|
||
|
||
|
||
|
||
Once the BootCamp software is downloaded, you can install it by executing `Setup.exe` or `\Drivers\Apple\BootCamp.msi` (`BootCamp64.msi` if present).
|
||
|
||
|
||
|
||
### Installing BootCamp 6 softare on unsupported machines
|
||
|
||
To get started, download the Brigadier utility from the following link:
|
||
|
||
* [Download Brigadier](https://github.com/timsutton/brigadier/releases/download/0.2.4/brigadier.exe)
|
||
|
||
Once Brigadier is downloaded, move it to your desktop for easy access.
|
||
|
||
Open up a command prompt window as a standard user and run `cd desktop`.
|
||
|
||
|
||
|
||
Then run `.\brigadier.exe --model=MacPro7,1`. This will download the latest BootCamp 6 package.
|
||
|
||
|
||
|
||
Once the BootCamp software is downloaded, you can install BootCamp 6 by executing `\Drivers\Apple\BootCamp.msi` in an administrator command prompt window.
|
||
|
||
|
||
|
||
## Troubleshooting
|
||
|
||
### "This version of Boot Camp is not intended for this computer model."
|
||
|
||
If you built OpenCore with Moderate or higher SMBIOS spoofing, you'll get an error when trying to install Boot Camp drivers. You can solve this by either rebuilding OpenCore with a lower spoof level, or running the installer from `Drivers/Apple/BootCamp.msi`.
|
||
|
||
| Setup.exe | BootCamp.msi |
|
||
| :--- | :--- |
|
||
|  |  |
|
||
|
||
::: details BootCamp.msi quirks
|
||
|
||
If needed, you can run it from the command line as administrator:
|
||
|
||
```
|
||
set __COMPAT_LAYER=WIN7RTM && start \path\to\BootCamp\Drivers\Apple\Bootcamp.msi'
|
||
```
|
||
|
||
Make sure to substitute `\path\to` with the location of the BootCamp folder.
|
||
|
||
You can also open `Properties` on the file to change the compatibility to `Previous version of Windows` in case you have BootCamp 4.0 drivers (the above command does this already.)
|
||
|
||
:::
|
||
|
||
### iMac12,x Bluescreen after driver installation
|
||
|
||
Currently Intel's iGPU drivers for the HD 3000 series do not support UEFI booting in Windows. The recommended solution is to simply disable the iGPU: [iMac 12,1 Windows 10 Boot Loop – Fix Intel Graphics issue](https://zzq.org/?p=39)
|